Tag Archives: Marble Tile Polishing

Restoring an Acid Etched Marble Tiled Kitchen Floor in Winchester, Hampshire

Posted on by

Marble is a natural material which although hard wearing can easily be ruined by a strong chemical such as acid. In this case my client’s kitchen floor which was laid with black Marble square tiles was etched due to the accidental spill of a corrosive agent and the subsequent attempt to clean it up.

Acid Damaged Marble Floor Tiled Kitchen Floor Before Renovation Winchester

The property was in the historic city of Winchester and as you can image my client was horrified by the state of their Marble floor which was now ruined. Desperate for a solution that didn’t involve the expensive tiles being replaced we were asked to take a look.

After surveying the floor, I recommended resurfacing the stone with a set of diamond encrusted floor burnishing pads which would remove the etching and hone the stone back to its original appearance.

Happy to discover there was a solution to the problem we were given instructions to go ahead with the restoration.

Honing Acid Etched Marble Floor Tiles

Our first task was to remove the kickboards from underneath the kitchen units, this ensures they are not scratched during the cleaning process and it also allows our buffer machine to get right to the edge of the floor.

I then started the burnishing process by applying a 400-grit coarse burnishing pad lubricated with a little water to the floor. This coarse pad will remove the etching and dirt from the Marble. It does generate a fine slurry on the floor so after each pad it’s best to rinse the slurry away with water and then extract it off the floor using a wet vacuum.

Following this, I worked my way through the remaining burnishing pads repeating the process with 800-grit medium and 1500-grit fine grit burnishing pads. I also used some small hand-held burnishing blocks in the difficult to reach corners and edges.

The floor pads struggle to reach into the recesses of the grout lines so halfway through the burnishing process I stopped to apply a dilution of Tile Doctor Pro-Clean along the grout lines and give them a scrub with stiff hand brushes repeating the process in stubborn areas.

After a final rinse the floor was left to dry off overnight.

Sealing Black Marble Floor Tiles

The next day I finished the polishing process by applying the last of the four pads in the set which is a very fine 3000-grit pad which refines the polish even further. This last pad is applied dry with only a little water sprayed onto the floor using a technique we call a ‘Spray Burnish”. The one of the advantages of this method is it leaves the floor dry so is ready for sealing.

Now that the appearance of the Marble had been restored it was time to protect the stone against future dirt, stains and damage by applying a sealer. On this occasion I chose Tile Doctor Colour Grow which is a colour enhancing product that really improves the depth of the black Marble tiles and increases the contrast with the white veins in the stone. Two coats of Colour Grow were applied allowing time for each coat to dry in-between coats. Once the sealant had hardened, I ran over the floor with a white buffing pad to further enhance the look of the Marble floor.

The Marble tile and grout was completely transformed much to the relief of the owner.

 

Source: Marble Tile Cleaning and Polishing Service in Winchester

Achieving a Deep Polish on Marble Floor Tiles in Reigate, East Surrey

Posted on by

The photographs below are of a Marbled Tiled floor that was installed over much of the ground floor of a cottage that formed part of a large county estate near Reigate.

Marble Tiled Floor Before Polishing Reigate Marble Tiled Floor Before Polishing Reigate

The Marble floor tiles were lovely however the polish and sealer had worn off some time ago and the were now looking much worse for wear, additionally the once white grout had turned dark with dirt and I`m not sure even the owner realised its full potential. I provided a quote for cleaning and applying a deep polishing to the floor which was agreed and set a date to do the work.

Marble Tile and Grout Cleaning in Reigate

After protecting the wooden skirting with tape, I started the cleaning process by applying a medium dilution of Tile Doctor Pro-Clean which was scrubbed into the tiles using a stiff brush to remove any loose dirt and debris from the floor but primarily along the grout lines. The soiled cleaning solution was then rinsed off with water and then extracted with a wet vacuum.

Next step was to deep clean the tiles and bring back the polish using a set of four Tile Doctor diamond encrusted honing pads which fit a weighted rotary floor buffer and are applied in sequence starting with the 400-grit pad lubricated with water. This is followed with the 800-grit and then the 1500-grit pads rinsing with water after each pad and removing the soil generated by the burnishing process with the wet vacuum as before.

This work took much of the day so after applying the 1500-grit pad and rinsing I left the floor to dry out overnight.

Sealing and Polishing Marble Tiles with Shine Powder

The next day I started by applying the 3000-grit pad which is the final pad in the polishing process and really helps bring up the polished appearance of the Marble. The pad is applied to the floor dry using a little water sprayed onto the floor using a process we call a spray burnish.

The last step was to seal the Marble tiles and build the polish even further by applying Tile Doctor Shine Powder which is diluted with water and buffed into the Marble tiles using a white buffing pad. The shine powder did an excellent job of building the shine on the floor and provides a tough durable finish that should last.

Marble Tiled Floor After Polishing Reigate Marble Tiled Floor After Polishing Reigate

After two days work the Marble tiled floor looked transformed and I was especially pleased with the deep level of shine and restored white grout that I had managed to achieve.

 

Source: Marble Tile Cleaning and Polishing Service in Reigate, East Surrey

Marble Shower Tile Damaged during End of Tenancy Clean in Bedfordshire

Posted on by

I was contacted by the owner of a cleaning company in Milton Keynes, after an end of tenancy clean at a house in Sharnbrook went wrong. Unfortunately a member of their staff had incorrectly applied an acid based cleaning product to the Marble shower tiles which like most natural stone is acid sensitive. The cleaning product had etched the stone causing the damage you can see below. Being a reputable company they were determined to put the situation right and we were asked to step in.

Marble Shower Cubicle Before Cleaning in Sharnbrook

We have had a few issues of this type before where customers keen to remove unsightly Limescale marks from their stone tiles use a household cleaner without reading the bottle label first to see if it’s safe to use. Issues of this nature on Marble cannot be easily resolved with chemical products; it takes specialist knowledge and equipment.

Marble Shower Cubicle Before Cleaning in Sharnbrook

The quote was given and accepted and the work was booked in with the letting company for a few weeks later.

Cleaning and Polishing a Marble Shower Cubicle

The first photos show the extent of the damage which had not only damaged the immediate area but as the cleaning product was in liquid form it had ran down the wall had totally ruined the surface of the tiles in the lower half of the shower.

The first thing I did was to protect the shower tray with towels and then began assembling the equipment needed for this job which consisted of a wet polisher, a variable speed polisher, one set of 6” Tile Doctor burnishing pads from 100 grit to 3,000 grit and one full set of diamond blocks from 80 grit upwards.

I then went about testing how far down the scale I would have to go to get the best results. I found that in most areas the application of a 200 grit burnishing pad was adequate to resurface the tile and remove damage but in some areas I had to go down the scale as low as 80 grit to achieve the desired result.

Marble Shower Cubicle During Cleaning in Sharnbrook

One the damage had been removed the higher grit pads are used in sequence to restore the polish finishing with the 3,000 grit pad. No chemicals are used in this process, just water and the small six inch diamond encrusted burnishing pads which fit to a hand buffer.

Although only a small area, no more than 4 m2 this job took most of the day. However, as the whole shower room was tiled in the same tiles it was a much more cost effective to restore the damaged tiles than replace them.

Marble Shower Cubicle After Cleaning in Sharnbrook

We were able to achieve an excellent result which the client was very happy with, no doubt saving the cleaning company thousands of pounds in replacement costs.

Marble Shower Cubicle After Cleaning in Sharnbrook

 
 
Source: Marble Tile Cleaning and Polishing Service in Bedfordshire

Restoring Ruined Marble Wall Tiles in a Surrey Shower

Posted on by

Marble tiles are a fantastic choice of stone for a shower cubicle because of its distinctive characteristics and quality. It can really add a luxurious feel and when used in a bathroom take it to the next level.

However, it’s extremely important to note that Marble like all natural stone is a porous and acid-sensitive material. It must therefore be cleaned with care using suitable products. This particular Marble tiled shower cubicle at a property in Leatherhead is a good example of this done wrong. The owner had used an acid-based cleaning product to clean the stone, resulting in damage to the sealer and causing unappealing streaks to form.

Marble Shower Wall Leatherhead Before Cleaning

This type of damage can appear irreparable but, with the right combination of cleaning methods and products, it can be fixed. Once the old sealer has been removed, and the tiles have been cleaned, polished and re-sealed, they can look as a good as new. Here’s how I helped this customer restore the Marble shower cubicle.

Cleaning and Polishing a Marble Shower Cubicle

To begin the restoration, I scrubbed the dirty grout lines using Tile Doctor Pro-Clean, which is a highly reliable and multi-purpose alkaline-based product. I then rinsed the tiles with water to remove the traces of cleaning product.

Next, I moved on to the polishing stage of the restoration – what we often refer to as burnishing. This involved the use of small six-inch diamond-encrusted burnishing pads applied with a hand buffer and with different levels of grit – ranging from Coarse to Very Fine. I started with the Coarse grit pad and worked my way sequentially through our four-pad system, polishing the stone with Medium, Fine and eventually the Very Fine pad to really bring up the polish.

Sealing a Marble Shower Cubicle

Once the shine had returned to the Marble and the damage had been removed, I re-sealed the tiles using two coats of Tile Doctor Colour Grow, a penetrating sealer designed to enhance the natural colours and patina of the stone. Once dry, I gave the tiles a final polish with a white buffing pad to put the finishing touches on the restoration.

Marble Shower Wall Leatherhead After Cleaning

The customer was thrilled with the results, saying:
“I’m really happy with the result and we will make sure we don’t use supermarket cleaners again on natural stone. Rupert was a very personable tradesman who took pride in what he was doing. He has identified Tile Doctor Neutral Tile Cleaner as being the product we should have used in the first place and has sent me the website details.”
Another satisfied customer!
 
 
Source: Marble Tile Cleaning and Restoration Service in Surrey